欢迎访问擎川机电设备有限公司网站!
定制咨询热线13533070862
擎川EVERLA > 知识问答 > 耐切输送带皮带适合用在切菜机使用吗?

知识问答

联系我们

擎川机电设备有限公司

邮 箱:everlas@163.com
手 机:135-3307-0862
电 话:400-9688-278
地 址:广东省广州市天河区东圃镇宦溪西路宦溪工业区12号A栋

耐切输送带皮带适合用在切菜机使用吗?

作者:擎川EVERLA输送带厂家 来源: 网络整理 更新时间:2021-07-28 17:06:03人气:

1、在保送带卷取铁芯上穿上转动灵敏的轴,并将带卷架好,上架前留意上、下盖胶的方向不要架反。

1. Put on a rotating sensitive shaft on the core of the coiling belt of the escort belt, and frame the tape well. Pay attention to the direction of the upper and lower cover glue before mounting the shelf.



耐切保送带

Shear-resistant belts

2、在不宜上架的工作场所能够把保送带卷导开,并使折叠处保送带具有足够大曲率半径,避免损伤保送带,折叠处制止在保送带上放置重物。

2. In workplaces that are unsuitable for shelving, the delivery belt can be rolled away, and the folded delivery belt can have a large radius of curvature enough to avoid damage to the delivery belt, and the folded part can stop placing heavy objects on the delivery belt.

3、假如是改换保送带,可将新带与旧带连在一同,卸带与装置新保送带同时停止。

3. If the belts are replaced, the new belts can be connected with the old ones, and the unloading belts and the new belts of the device can be stopped at the same time.

4、关于程度运转的保送机,可在任何一点切断旧保送机,倾斜方向运转的保送机,则需选好切断点,避免因自重惹起下滑而失控。

4. Regarding the degree of operation of the conveyor, the old one can be cut off at any point. If the conveyor runs in an inclined direction, the cut-off point should be selected to avoid the loss of control caused by the weight.

5、在保送机上将新带的位置放正后,用夹具将胶带的一端固定好,然后绕过辊与带轮的绳索相连,经过牵引安装将保送带均衡的架到保送机上,牵引时,要避免保送带与机架互相挤压。

5. After positioning the new belt on the delivery machine, fix one end of the belt with fixture, then connect the belt with the rope of the pulley by bypassing the roll. After traction and installation, the delivery belt is balanced on the delivery machine. When traction, it is necessary to avoid squeezing each other between the delivery belt and the frame.

6、用夹具将保送带的一端固定在保送机架上,另一端经过滑轮将另一端拉紧,直到保送带在返回托辊上无明显下垂。

6. Fix one end of the belt on the shelf with fixture, and the other end is tightened by pulley until there is no obvious sag of the belt on the return roller.

7、将张紧安装固定离起点100~150mm。

7. Fix the tension installation from the starting point of 100-150 mm.

本文由切菜机输送带友情奉献.有关的知识请点击:http://www.everla.cn真诚的态度.为您提供为全面的服务.有关的知识我们将会陆续向大家奉献.敬请期待.

This article is dedicated by the friendship of the cutting machine conveyor belt. For more knowledge, please click on: http://www.everla.cn sincere attitude. To provide you with comprehensive services. More relevant knowledge will be dedicated to you one after another. Please look forward to it.